Conforme à VDI 6022
Les unités décentralisées en allège type FSL-B-ZAB apportent de l'air neuf climatisé aux bâtiments.
En plus de la ventilation avec récupérateur de chaleur et filtration de l'air, le chauffage et le refroidissement des espaces de bureaux sont garantis.
rectangular
Outside air:
16 – 33 l/s
60 – 120 m³/h
W: 1065 mm
H: 1065 mm
D: 195 mm
Cooling capacity up to 460 W
Heating capacity up to 800 W
The fresh/outdoor air enters directly through an opening in the façade. There is a spring return motorised shut-off damper (11) located at the bottom of the unit in the outdoor air inlet(12), this closes the inlet when the unit is inactive or in the case of a power failure. The exhaust air damper is coupled to the outside air damper by means of a connecting shaft (16) and the system is operated by a single actuator.
The fresh air is cleaned using an F6 fine dust filter (2) and then passes through an automatic mechanical flow rate controller (21) which limits the fresh air flow rate to a set maximum. Then the air passes through a recuperative heat recovery unit (3) in which part of the heat energy from the extract air is transferred to the inlet fresh air. A radial supply fan (5) then discharges the air through a 4 pipe coil with heating and cooling capacity. The air is finally discharged into the room through an under sill slot with a displacement flow characteristic. The extract air is taken from the upper sill area then passes through a G3 coarse dust filter (1). After this the air passes through the recuperative heat recovery unit (3). When in energy saving mode, in a transitional period, or for anti icing protection, a motorised bypass damper (9) is opened which bypasses the heat recovery system (3). The exhaust air fan (6) produces the necessary pressure differentials for the extract system. The motorised shut-off damper (11) with spring return actuator closes the exhaust air outlet when the system is shut down or in the case of a power failure.
The type FSL-B-ZAU model Capricorn can provide three flow rates 60/90/120 m3/h. All three settings can operate on full recirculation or full fresh air (as described above). For full fresh air, to achieve this the BMS opens the inlet and exhaust air dampers (11) and closes the recirculation damper (8). The BMS operates the supply air and exhaust air fans in parallel at the required level.
For full recirculation the fresh air inlet and exhaust air dampers (11) are closed and the recirculation damper (8) is opened.
In this case the exhaust air fan is switched off by means of a relay and the supply air fan is operated by the BMS to provide three flow rates with full recirculation.
The units can additionally operate in an asynchronous balanced mode. To achieve this, the fresh air inlet and exhaust air dampers (11), as well as the recirculation damper (8), must be opened. In this mode a second relay which is integrated into the unit switches the exhaust air fan on, providing a constant flow rate independent of the BMS requirements, this is at speed one providing 60 m3/h. If the fan is activated from central control and operates at speeds two or three, this only effects the supply air fan. The result is that the exhaust air is at a constant flow rate of 60 m3/h and the fresh/outside air supply is at 60 m3/h and depending on the actual fan setting there is a recirculation air flow of 30 m3/h or 60 m3/h for fan speeds two and three respectively. If the minimum fresh/outdoor air is being used with fan speeds two and three this mixing operation can save substantially more energy in the heating or cooling modes than when in the full fresh air mode due to the benefits of thermal recovery.
Partager la page
Recommander cette page
Vous avez la possibilité de recommander cette page en partageant le lien.
Contact
Merci pour votre message !
Votre recommandation a été envoyée et sera bientôt reçue par le destinataire.
Contact
Nous sommes à votre disposition
Veuillez spécifier le sujet de votre requête et vos coordonnées.
Tel.: +33 1 56 70 54 54
Contact
Merci pour votre message !
Votre message a été reçu par le Centre de Service et est en cours de traitement.
Notre département des demandes de service vous contactera sous peu.
Si vous avez des questions d'ordre général sur nos produits et services, vous pouvez également nous contacter à l'adresse suivante:
Tél .: +49 (0) 2845 2020 | Fax: +49 (0) 2845 202265
Contact
Nous sommes à votre disposition
Veuillez spécifier le sujet de votre requête et vos coordonnées.
Tel.: +33 1 56 70 54 54
Contact
Merci pour votre message !
Votre message a été reçu par le Centre de Service et est en cours de traitement.
Notre département des demandes de service vous contactera sous peu.
Si vous avez des questions d'ordre général sur nos produits et services, vous pouvez également nous contacter à l'adresse suivante:
Tél .: +49 (0) 2845 2020 | Fax: +49 (0) 2845 202265